Setting up Ad-hoc connection on WinCE device using Network Driver IOCTLs and OIDs
I am creating a library for Win CE 5.0 in eVC++ 4.0. This library will allow application developers to programmatically set up wireless connection.
I have decided to use DeviceIoControl function to communicate with network driver using Network Driver IOCTLs and OIDs ( for reference see Network Driver Reference ).
To set up wireless connection using infrastructure mode I do following operations:
1. Set OID_802_11_INFRASTRUCTURE_MODE to value Ndis802_11Infrastructure
2. Set OID_802_11_AUTHENTICATION_MODE to value Ndis802_11AuthModeOpen or Ndis802_11AuthModeShared
3. Set OID_802_11_WEP_STATUS to value Ndis802_11WEPDisabled or Ndis802_11WEPEnabled
4. If WEP is enabled, set OID_802_11_ADD_WEP to value of specified WEP key and index
5. Set OID_802_11_SSID to value of specified network name
This works for me.
Now, what is my problem:
I am trying to set up Ad-hoc (IBSS mode) connection, so I simply tried to change Ndis802_11Infrastructure to Ndis802_11IBSS in the first step. But it does not work (connection is not successfully set-up).
I also set up static addresses on both devices which I was trying to interconnect and I have switched off WZCTOOL in "Advanced Wireless Settings" dialog. (I think that WZC service cannot be disabled on my device, because it is not listed in "services list" command output.)
I think I am missing some operations to be done or I am using incorrect order of operations which I have stated above.
I will appreciate your help. Thanks.
what is the error message you're getting? It could be an authrozation problem, unsupported mode, and just about a dozen more causes?
Danny, thank you for your reply.
Originally Posted by Danny
About error message:
As I wrote, I use DeviceIoControl function. To set those settings I use 'IOCTL_NDISUIO_SET_OID_VALUE' as a dwIoControlCode parameter.
Now, this DeviceIoControl function is successful in all calls I have listed previously. So I am getting no error message.
I have no clue what I am doing wrong.
I have made a test to interconnect two wireless devices (WinCE 5.0 platform) using Ad-hoc mode:
1. I set appropriate static IP addresses on both devices (when device is disconnected, 'ipconfig' command will show '0.0.0.0' IP address);
2. On 1st device I added new Ad-hoc network using WZCTOOL (No WEP, Open auth.);
3a. On 2nd device, when that new network had shown on available network list, I chose it from the list and instructed WZCTOOL to connect to it. Then 'ipconfig' shown static IP address which I had previously set in step 1 and systray icon of the wireless interface indicated connected state. So, it worked when I used only WZCTOOL.
3b. As an alternative to the step (3a), I tried to use 'DeviceIoControl' function and IOCTLs and OIDs (on 2nd device) which I have described in my first post (I had disabled WZCTOOL on 2nd device first). All DeviceIoControl calls were successful, but neither 'ipconfig' shown non-zero IP address nor systray icon indicated connected state.
Maybe this would clarify my problem.
As per ur steps for wireless connection using Infrastructure Mode is not working for me:
Could please check out the below code for any problems:
I am working on WM5.0 + PocketPC + Visual studio 2005
HRESULT Cap_listDlg::SetNetworkMode(int *pnNetworkMode)
UCHAR SetBuffer[sizeof(NDIS_OID) + sizeof(NDIS_802_11_NETWORK_INFRASTRUCTURE)];
m_hRes = E_POINTER;
pSetOid = (PNDISUIO_SET_OID) &SetBuffer;
pSetOid->ptcDeviceName = _T("TIACXWLN1");//m_DeviceName;
pSetOid->Oid = OID_802_11_INFRASTRUCTURE_MODE;
memcpy(&pSetOid->Data, pnNetworkMode, sizeof(NDIS_802_11_NETWORK_INFRASTRUCTURE));
m_dwError = GetLastError();
fprintf(ap_fp,"IOCTL SET_NETWORK_MODE failed: %d\n", m_dwError);
m_hRes = E_FAIL;
The same case for Authentication case also.
But I am able to set SSID.
Could please send me ur code for wireless connection in infrastructure mode or just send what's problem in the above code
I am facing the same problem of setting the oid
Originally Posted by phani.dv
my deviceiocontrol returns 0 but value is not set
were you able to solve this problem
Did you resolve the problem? I would like to do the same
Originally Posted by vasudhaverma
-- Android Development Center
-- Cloud Development Project Center
-- HTML5 Development Center
-- Windows Mobile Development Center